If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Unconfigured Ad Widget
Collapse
Announcement
Collapse
No announcement yet.
Free HUAWEI voice functions activation (beta) ONLY here
Try please other provider sim, also be sure signal strength is not to low.
Arunas try to enable voice and send AT^CVOICE? to modem. it returns 0 - which is correct - its PC Voice Mode. Now send AT^U2DIAG=255 command and reinsert modem. Send AT^CVOICE? and it will return 1 which means Earphone Mode. Not good - after AT^U2DIAG=255 it restores factory defaults from nvram.
1) Click Start > Run > Type hypertrm > [Enter]
2) In the window that opens type any friendly name e.g. 3G Huawei > [OK]
3) Keep the default values, except Connect Using where you must select your modem > [OK]
4) click [Modify] > [Settings] > [ASCII Setup]
5) Tick 'Echo typed characters locally' > [OK] > [OK] > [Cancel]
6) In the main HyperTerminal Window type AT^U2DIAG=256
(or AT^U2DIAG=276 or AT^U2DIAG=255)
7) [Enter]
Note: If you have connection problems (ie. you don't see OK after pressing enter to send the command) click to icon to disconnect. then go to file > properties and change your port. and try again [DC-U shows which ports the modem uses]
The SD and NAND were detected again using AT^U2DIAG=276 in the beta console window.
Thanks.
Any reason to have this function so that it can be turned off as well as on?
Same as previous poster too, I would like a way to update the NAND with newer Mobile Partner, unless anyone knows a dashboard update that will do this?
manufacturer - Huawei datacards
model - Auto detect
Found modem : E160
Model : Huawei E160/E160G/E160X
IMEI : ************
Firmware : 11.608.08.81.00
Dashboard version : UTPS11.030.01.04.03
Serial NR. : **************
SIM Lock status : unlocked
Voice feature : enabled
Wrong codes entered : 0 (unlock attempts left : 10)
I now have problem of dead modem.
I did the update which seem to go smoothly It then did restore user settings going fine until reached 100% then it froze on me I left it forabout 15 minutes but nothing happend and saw that in device showed as unknown device.
Now not seen by PC so cant do anything with it,.
Is there any program that can force flash the e160g or should I just Bury it
I now have problem of dead modem.
I did the update which seem to go smoothly It then did restore user settings going fine until reached 100% then it froze on me I left it forabout 15 minutes but nothing happend and saw that in device showed as unknown device.
Now not seen by PC so cant do anything with it,.
Is there any program that can force flash the e160g or should I just Bury it
After posting the above I left it for 10 minutes and then tried modem in different USB port and it was seen and successfully activated Voice in version 412 although v411 reported card not found.
DC - Unlocker 2 Client 1.00.0412 beta
Detecting card :
selection :
manufacturer - Huawei datacards
model - Auto detect
Found modem : E160G
Model : Huawei E160/E160G/E160X
IMEI : 35************
Firmware : 11.608.08.81.00
Dashboard version : HUAWEI_BUILD_36
Serial NR. : DL5TAA1863019805
SIM Lock status : unlocked
Voice feature : enabled
Wrong codes entered : 0 (unlock attempts left : 10)
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment