Mate 10 pro board software non encrypted

[gsmgeo]

Does the computer detect your device? If yes, just install one of the two board software for the BLA, customize with the HCU and then install the full firmware with data.

see my post .
oday connect my Mate 10 pro BLA-A09 with test point
28.05.2018 14:30:01 Starting to write device in FASTBOOT mode...
File to update: BLA-A09-BD_1.0.0.36_Board_Software_Android_8.0.0_EMUI_8.0. 0_05022GPJ.dgtks
Device detected:
COM37: HUAWEI USB COM 1.0 (COM37)

Writing bootloader...
Writing BLA-A09-BD_1.0.0.36_Board_Software_Android_8.0.0_EMUI_8.0. 0_05022GPJ_3.dtwork...
Error writing Bootloader
28.05.2018 14:30:26 Writing device finished - INCOMPLETE
************************************************** ************************
you had not bricked

[k4fari]

Not needed, you can use that available here. I managed to recover a Mate 10 Pro BLA hardbricked using one or both of board software with Dc Phoenix

Are you sure? Hard bricked means phone is detected only in USB-SER / USB Com 1.0. Was your phone in same condition? How did you managed to wrire board firmware? I think your phone was not bricked by a software update as our phones was bricked by installing new firmwares Alp-l29c636b134 and Bla-l29c636b137.

[Chaserxx]

Are you sure? Hard bricked means phone is detected only in USB-SER / USB Com 1.0. Was your phone in same condition? How did you managed to wrire board firmware? I think your phone was not bricked by a software update as our phones was bricked by installing new firmwares Alp-l29c636b134 and Bla-l29c636b137.

Look, yes my phone was in hardbrick, whose situation is found after update by you mentioned. You need the correct drivers for the Phoenix Dc to communicate with the device, at the same time that you have to insist by pressing the power plus volume less until the program recognizes and begin to install the firmware board. After installation I think you know how to proceed ...

[gsmgeo]

Look, yes my phone was in hardbrick, whose situation is found after update by you mentioned. You need the correct drivers for the Phoenix Dc to communicate with the device, at the same time that you have to insist by pressing the power plus volume less until the program recognizes and begin to install the firmware board. After installation I think you know how to proceed ...

your phone turned on in fastboot ))) and not USB SER/USB COM

[Chaserxx]

Nah man, I'm talking about another mate 10 pro, this one is Hardbricked caused by update to this builds.

I have some devices fixed, mate 10 pro, p20/Lite pro, Honor 8/9

[gsmgeo]

Does the computer detect your device? If yes, just install one of the two board software for the BLA, customize with the HCU and then install the full firmware with data.

Yes he finds USB SER, probably you had an old version, you were lucky.
from 3 phones so far at me one has joined

[k4fari]

Has any one tired DC Phoenix new version V55 ?

[berkayyildiz93]

Look, yes my phone was in hardbrick, whose situation is found after update by you mentioned. You need the correct drivers for the Phoenix Dc to communicate with the device, at the same time that you have to insist by pressing the power plus volume less until the program recognizes and begin to install the firmware board. After installation I think you know how to proceed ...

Hello there. Did you see that the mate 10 pro device with hardbrick case (usb ser / com port) works with dc phoenix? Which version do we need to use dc phoenix? There are 2 board software for BLA, but in both the write bootloader gives an incomplete error. Do we need to press a key on the phone after starting the dc writing process in Phoenix?

[Chaserxx]

Hello there. Did you see that the mate 10 pro device with hardbrick case (usb ser / com port) works with dc phoenix? Which version do we need to use dc phoenix? There are 2 board software for BLA, but in both the write bootloader gives an incomplete error. Do we need to press a key on the phone after starting the dc writing process in Phoenix?

Hello.

Use the latest version of Dc Phoenix, if the manager recognizes the cell phone as usb_ser install the correct drivers theninstall the board software. Any one of them, if one does not work, try another.
The board software will install the boot sector and after that your pc will recognize the mobile in fastboot mode.

[berkayyildiz93]

Hello.

Use the latest version of Dc Phoenix, if the manager recognizes the cell phone as usb_ser install the correct drivers theninstall the board software. Any one of them, if one does not work, try another.
The board software will install the boot sector and after that your pc will recognize the mobile in fastboot mode.

I have 3 board software.

BLA-A09-BD_1.0.0.36_Board_Software_Android_8.0.0_EMUI_8.0. 0_05022GPJ
BLA-AL00B_1.0.0.35_Board_Software_China_Nonspecific_An droid_8.0.0_EMUI_8.0.0_05022FPT HalabTech
BLA-AL00B-BD_1.0.0.36_Board_Software_Android_8.0.0_EMUI_8.0. 0_05022FPT

V52, v56, v57 Dc phoenix versions of 3 software I tried repeatedly. The same mistake in all of them. 'Write bootloader: incomplete'



Today, I came across a new method. I share the link, the video is in the link. Does it work for you? A new method. Shared on June 8th.

http://forums.easy-firmware.com/showthread.php?232485-How-to-Flashing-Huawei-Board-Software

[berkayyildiz93]

Yes he finds USB SER, probably you had an old version, you were lucky.
from 3 phones so far at me one has joined

BLA-AL00B-BD_1.0.0.36_Board_Software_Android_8.0.0_EMUI_8.0. 0_05022FPT.dgtks


Have you tried this software that was shared on June 13? I got the same error

But hope is born, please check the link that I share in the top message.