P10 Lite DcPhoenix

[quajskwi]

Hi guys,
I'm trying to recover my P10 Lite (locked + FRP lock, WAS-LX1A 8.0.0.383(C432)) using DC Phoenix.
So I downloaded Warsaw-L21_8.0.0.380(C432)_Firmware_8.0.0_r1_EMUI8.0_0501 4JKK.APP and try to update in standard mode, but it stops the process and disconnect the phone (first of it visible as Android sooner single adb interface in device manager). On the phone I can read the message "Your device has been unlocked and can't be trusted.. etc" and this is the sw log:

DC Phoenix 0.0.0.126
user:quajskwi


Standard update
Not Reboot NOT cheked
Update Verlist to server on file load NOT checked
Try Rescue Recovery checked
Bypass version check checked
Old slow algo checked

Looking for a device in upgrade mode
No devices detected in upgrade mode
Device found: H3XDUXXXXXXX2663

Extracting recovery partition

Extracting partition: ERECOVERY_KERNEL
ERECOVERY_KERNEL partition extracted

Extracting partition: ERECOVERY_RAMDISK
ERECOVERY_RAMDISK partition extracted

Extracting partition: ERECOVERY_VENDOR
ERECOVERY_VENDOR partition extracted

15/04/2020 22:43:00 Starting to try Rescue Recovery...


Looking for a device in fastboot mode
Device found: H3XDUXXXXXXX2663


Getting IMEI...
Getting build number...
Getting model ...
Getting battery state...
Getting backdoor info...
Getting lock state info...
Getting lock boot info...

SN:H3XDUXXXXXXX2663
IMEI:8673150XXXXXXXX
IMEI1:000000000000000
MEID:00000000000000
Build number: :WAS-LX1A 8.0.0.383(C432)
Model: WAS-LX1A
Vendor/Country: hw/eu
Battery state: 4174mv
OEM lock state info:
FB LockState: LOCKED
USER LockState: LOCKED
OEM get bootinfo:
locked


Process identifier:23928923


Erasing ver .. .
Cannot get FBlock info from device
Trying to unlock device...

Signing process may take few minutes

Trying to get data from server
Waiting in queue for signing service. Expected time 1 second(s) to get data from server

Trying to get data from server
Unlock process finished successfully


Erasing ver .. .
Writing rescue_recovery_kernel partition
RESCUE_RECOVERY_KERNEL partition update ...OK
Writing rescue_recovery_ramdisk partition
RESCUE_RECOVERY_RAMDISK partition update ...OK
Writing rescue_recovery_vendor partition
RESCUE_RECOVERY_VENDOR partition update ...OK
Uptade recovery parttion OK

USB Device REMOVAL
Type: @oem86.inf,%hwfastboot%;Android Sooner Single ADB Interface
VidPid: VID_18D1&PID_D00D
Instance id: H3XDUXXXXXXX2663


How can I recover my phone, please?

[gsmgeo]

Hello
check recovery and erecovery mode
now its run ?

[quajskwi]

thanks for your support.
it seems no recovery yet:
volume up + power button lead to huawei logo over and over.
I let the battery drain completely, plug in and hard reset again: logo huawei

[gsmgeo]

thanks for your support.
it seems no recovery yet:
volume up + power button lead to huawei logo over and over.
I let the battery drain completely, plug in and hard reset again: logo huawei

I think that there may be technical problems.
Tip
disassemble the phone and try to disconnect the cameras on the phone, and check. If it does not help, try flashing the board firmware using the testpoint. I am sure you will succeed.
There will be questions, ask

[quajskwi]

I cannot force to update mode when it stops the update standard procedure...
The bootloop is due to an update OTA failed, I guess... the phone was working perfectly until the night, next morning i found it with the stuck logo... For the flashing using the testpoint i have to disassemble and shortcircuit that pin in pic? Is there a tutorial or somehow?

[gsmgeo]

I cannot force to update mode when it stops the update standard procedure...

hm
you open phone ?