Announcement

Collapse
No announcement yet.

DC-Phoenix

Collapse
This is a sticky topic.
X
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Valdemaras
    started a topic DC-Phoenix

    DC-Phoenix

    DC-Phoenix download software >>here<<
    Supported models and features list here
    Files we have can review here Download possible only from DC-Phoenix directly


    Exclusive features :
    Repair Huawei firmware problems (Bricked, Bootloop, stuck on Fastboot mode etc.)
    Can write firmware by fastboot with locked bootloader and locked FRP!
    Huawei Firmware UPDATE.APP file direct writing in fastboot
    Full/partial erase and write full factory images in fastboot (DC Unlocker factory images in format DGTKS)
    Full/partial erase and write full factory images by testpoint
    Any rom writing in fastboot without signature and compatibility checking!
    Flashing bricked Huawei phones in qualcomm 9008 mode.
    Flashing bricked Huawei phones in Huawei 1.0 mode (VID_12D1&PID_3650).
    Flashing bricked phones where no Huawei 1.0 or 9008 visible by testpoint

    Warning




    1. HCU timed license account advised
    2. DC-Phoenix allows to flash any file into phone, it is not being validated by our software or by phone - be very careful what you write into your device!
    How to repair bricked Huawei phone




    SUPPORTED Models & in what conditions you can flash them

    Method 1:
    Can be used when phone in bootloop, stuck in fastboot etc.

    WARNING: DO NOT USE BOARD SOFTWARE FROM OUR SUPPORT AREA FOR METHOD 1

    Step 1

    Write firmware (and customization) file from DC-Phoenix support area (or elsewhere) in fastboot with DC-Phoenix.

    Select "Standard" mode. DC-Phoenix will flash phone in fastboot and finish flashing in upgrade mode at once.

    Huawei Phone flash in fastboot GUIDE

    WARNING: Unfinished flashing in upgrade mode may cause problems: wrong RAM, internal memory size and others.

    NOTE: If you get error during flashing "VERLIST partition" it means your customization version is not same as before, you must do Step 2!

    Step 2 (not required if flashing successful in Step 1)

    After flashing in fastboot, phone should be able to boot up now
    Now you need to rewrite vendor & country even if it remains same. They must match with customization file that you have flashed.

    NOTE: keep in mind that Vendor/Country and Model fields are case sensetive!

    HCU repair guide HERE
    After repair on HCU repeat Step 1

    Method 2:
    For phones that do not turn on after completing Method 1 soluton

    Step 1

    Start device repair with factory firmware flash (Can use any Board firmware for any model version - NXT-AL10 Board firmware fits all NXT-xxxx versions etc., same for others)
    Select all files at once: Board software, firmware, customization following your model.

    Huawei phone board software flash GUIDE

    NOTE: If you get error during flashing "VERLIST partition" it means your customization version is not same as before, you must do Step 2!

    Step 2 (not required if Step 1 flashing successful)

    After flashing in fastboot, phone should be able to boot up now
    Now you need to rewrite vendor & country even if it remains same. They must match with customization file that you have flashed.

    NOTE: keep in mind that Vendor/Country and Model fields are case sensetive!

    HCU repair guide HERE
    Then repeat Method 1

    Step 3 (required if no imei, sn, mac or other data missing)

    HCU repair as empty board guide HERE

    Method 3:
    (with testpoints, Huawei USB COM 1.0 or 9008 port visible)

    Step 1

    Start device repair with factory firmware flash (Can use any Board firmware for any model version - NXT-AL10 Board firmware fits all NXT-xxxx versions etc., same for others)
    Select all files at once: Board software, firmware, customization following your model.

    9008 port visible flashing GUIDE

    Huawei USB COM 1.0 port visible flashing GUIDE

    IMPORTANT: Board software/firmware/customization files available on our support area, which is accessed from DC-Phoenix

    (If Huawei USB COM 1.0 (VID_12D1&PID_3650) or 9008 port not visible)
    Press "View Testpoint" button to see testpoint location picture. Short-circuit these pin-points. If there is only one testpoint shown then short circuit it with GND

    Flashing with testpoint GUIDE

    NOTE: If you get error during flashing "VERLIST partition" it means your customization version is not same as before, you must do Step 2!

    Step 2 (not required if Step 1 flashing successful)

    After flashing in fastboot, phone should be able to boot up now
    Now you need to rewrite vendor & country even if it remains same. They must match with customization file that you have flashed.

    NOTE: keep in mind that Vendor/Country and Model fields are case sensetive!

    HCU repair guide HERE
    Then repeat Method 1

    Step 3 (required if no imei, sn, mac or other data missing)

    HCU repair as empty board guide HERE
    Last edited by Valdemaras; 2018-12-21, 04:58 PM.

  • kurvenmeister
    replied
    "error writing bootloader", could not find a testpoint file for oreo
    to all cracks out there. need advices and correct software for flashing my honor 8 pro with dc phoenix by method 3 testpoints. phone was on stock emui oreo before bricked. tried all testpoint files from the download section. tried once again every loadable testpoint file. no one is working. please help.
    Last edited by kurvenmeister; 1 week ago.

    Leave a comment:


  • Valdemaras
    replied
    Originally posted by gagarinets View Post
    I bought 19 credits,I could not use it,my Honor 9 is not in support,please return the money
    Please more details.

    Leave a comment:


  • gagarinets
    replied
    I bought 19 credits,I could not use it,my Honor 9 is not in support,please return the money
    Hello, why do not they weigh me? 3 days end again, but I can not restore my Honor 9

    Leave a comment:


  • ytim08
    replied
    I have yet again bricked my device(lol). But now it is on January 2019 security patch. It is an Honor 7x(Mate SE). If you ever are able to exploit this security patch please keep me posted! As I have noticed you cannot flash oeminfo on this version, I have not checked most recently and do NOT want to buy another trial just do be disappointed.

    Leave a comment:


  • Valdemaras
    replied
    Originally posted by sb7206 View Post
    Hello,

    Yesterday I bought a 3 days license to try to unbrick my Honor 8 (model rebranded end 2016 from FRD-AL00 to FRD-L09, bricked for more than a year following an official OTA update).
    I was able to flash a few different firmwares but the only one working during all my tests was the latest FRD-AL00.
    Then I tried FRD-L09 8.0.0.521(C432) and it seems definitely bricked:
    - While booting: ERROR MODE, Please update your system again, Func NO: 15 (bl31 image), Error NO: 1 (security verify failed)
    - When going in fastboot mode, DC Phoenix reports "Device with unsupported security patch" and all updates fail as "not allowed".

    Any chance to unbrick it?

    Thanks in advance and best regards,
    Serge

    ---

    Details:
    Looking for a device in upgrade mode
    No devices detected in upgrade mode
    Device found: WTK7N16926005327


    03/03/2019 18:15:27 Starting to write device in FASTBOOT mode...
    Current version: FRDC00B001


    Looking for a device in fastboot mode
    Device found: WTK7N16926005327

    SN:WTK7N16926005327
    IMEI:xxx
    IMEI1:xxx
    Build number: :FRD-L09C432B381
    Model: FRD-L09
    Battery state: 4531mv

    Device with unsupported security patch
    User accepted to update device with unsupported security patch

    Writing RECOVERY partition
    RECOVERY partition UPDATE :FAIL Command not allowed

    Device with unsupported security patch
    03/03/2019 18:16:05 Writing device finished - INCOMPLETE


    Maybe only by trying to use loader+oeminfo solution from update oeminfo tab on dc-phoenix.

    Leave a comment:


  • sb7206
    replied
    Hello,

    Yesterday I bought a 3 days license to try to unbrick my Honor 8 (model rebranded end 2016 from FRD-AL00 to FRD-L09, bricked for more than a year following an official OTA update).
    I was able to flash a few different firmwares but the only one working during all my tests was the latest FRD-AL00.
    Then I tried FRD-L09 8.0.0.521(C432) and it seems definitely bricked:
    - While booting: ERROR MODE, Please update your system again, Func NO: 15 (bl31 image), Error NO: 1 (security verify failed)
    - When going in fastboot mode, DC Phoenix reports "Device with unsupported security patch" and all updates fail as "not allowed".

    Any chance to unbrick it?

    Thanks in advance and best regards,
    Serge

    ---

    Details:
    Looking for a device in upgrade mode
    No devices detected in upgrade mode
    Device found: WTK7N16926005327


    03/03/2019 18:15:27 Starting to write device in FASTBOOT mode...
    Current version: FRDC00B001


    Looking for a device in fastboot mode
    Device found: WTK7N16926005327

    SN:WTK7N16926005327
    IMEI:xxx
    IMEI1:xxx
    Build number: :FRD-L09C432B381
    Model: FRD-L09
    Battery state: 4531mv

    Device with unsupported security patch
    User accepted to update device with unsupported security patch

    Writing RECOVERY partition
    RECOVERY partition UPDATE :FAIL Command not allowed

    Device with unsupported security patch
    03/03/2019 18:16:05 Writing device finished - INCOMPLETE



    Leave a comment:


  • ytim08
    replied
    Originally posted by Valdemaras View Post

    Very much doubtful.
    You were right. However, I flashed the L21 OEM info and service-rom and it fixed it! Thank you so much! <3
    And I reused the unlock key I got from you guys a few days ago and it worked!

    Leave a comment:


  • Valdemaras
    replied
    Originally posted by ytim08 View Post
    I'm wondering, is flashing OEM necessary if I know the Google account that is causing the FRP? I know why my device is bricked(poorly configured .prop files). Can I just flash the UPDATE.APP and it should be good?
    Very much doubtful.

    Leave a comment:


  • ytim08
    replied
    I'm wondering, is flashing OEM necessary if I know the Google account that is causing the FRP? I know why my device is bricked(poorly configured .prop files). Can I just flash the UPDATE.APP and it should be good?

    Leave a comment:


  • vinnom
    replied
    Originally posted by Valdemaras View Post

    Refund now completed.
    Thx
    I would be happier if I could ressurrect the phone, but as I couldn't, I appreciate how fair you handle this =)

    Leave a comment:


  • Valdemaras
    replied
    Originally posted by vinnom View Post
    I took the output and copied to a txt file. The output of OEMINFO write and the update process are attached [ATTACH]n178512[/ATTACH] [ATTACH]n178513[/ATTACH]
    Refund now completed.

    Leave a comment:


  • vinnom
    replied
    I took the output and copied to a txt file. The output of OEMINFO write and the update process are attached oeminfo.txt update.txt

    Leave a comment:


  • vinnom
    replied
    Originally posted by Valdemaras View Post

    What is your username? You should try on this version https://files.dc-unlocker.com/get/75...5899b8f3502e6f

    "I'm also getting error after flashing the Update file. It gets flashed fine, but when customization file tries to get flashed, I get an error with AMSS_VERLIST; Can I assume that this occurs because of OEMINFO which didn't get write correctly?" - We won't know this.
    the username is bl2362. Ok, I'll try this version of DC-Phoenix, thanks

    Leave a comment:


  • Valdemaras
    replied
    Originally posted by vinnom View Post
    Hi, I'm trying to get my device back to work.

    While using DC-Phoenix, I'm trying to write the OEMINFO so I can flash the customization file.

    My device is CAN-TL10 and I already saw at the device list that it is supported for this operation.

    I tried once to do the same I'm doing now (method 1 from the guide) but I didn't pay attention at the first time to the correct vendor and region. The problem is that I'm getting this message when trying to write the OEMINFO:

    " Writing device finished - INCOMPLETE
    Exception: Access violation at address 00A3C666 in module 'DCPhoenix_v69.exe'. Read of address 00000000"

    thanks

    EDIT:

    I'm also getting error after flashing the Update file. It gets flashed fine, but when customization file tries to get flashed, I get an error with AMSS_VERLIST; Can I assume that this occurs because of OEMINFO which didn't get write correctly?
    What is your username? You should try on this version https://files.dc-unlocker.com/get/75...5899b8f3502e6f

    "I'm also getting error after flashing the Update file. It gets flashed fine, but when customization file tries to get flashed, I get an error with AMSS_VERLIST; Can I assume that this occurs because of OEMINFO which didn't get write correctly?" - We won't know this.

    Leave a comment:

Working...
X