DC-Phoenix

[Steve-1]

sorry problem solved

[Samiral]

Sorry my english (google translate)

Looking for a device in upgrade mode
No devices detected in upgrade mode
Looking for a device in fastboot mode
Device found: QMU7N18130000430
20.10.2018 9:22:53 Starting to write device in FASTBOOT mode...
Device found: QMU7N18130000430
Cannot get IMEI from device
Build number: :ALP-LGRP2-OVS 9.0.0.108(log)
Product model: ALP-L29
Batery state: 5650mv
Device not supported


Since the phone model is not supported, is it possible to refund the money spent on loans (the name Samiral1)?

[kenchanfr]

Device: Mate 10 Pro
Enter Phone Model:BLA-L29(C636)
Version number: BLA-L29 8.0.0.143 (C636patch01)
Security Patch Level: 2018/08/01 Androld Program Security Patch Level

Use the program (HWOTA8_Mate10) to lower the Firmware as follows:
From the original system BLA-L29C636B143-SP1 (8.0.0.143)
Reduced to BLA-L29C636B128 (8.0.0.128)
After rebooting, the result turns into a black brick. It can't be turned on and cannot be charged, but the computer can find the phone, and the device administrator appears USB SER.

Can this be solved?
thank

[Valdemaras]

Sorry my english (google translate)

Looking for a device in upgrade mode
No devices detected in upgrade mode
Looking for a device in fastboot mode
Device found: QMU7N18130000430
20.10.2018 9:22:53 Starting to write device in FASTBOOT mode...
Device found: QMU7N18130000430
Cannot get IMEI from device
Build number: :ALP-LGRP2-OVS 9.0.0.108(log)
Product model: ALP-L29
Batery state: 5650mv
Device not supported


Since the phone model is not supported, is it possible to refund the money spent on loans (the name Samiral1)?

Refund completed.

[Valdemaras]

Device: Mate 10 Pro
Enter Phone Model:BLA-L29(C636)
Version number: BLA-L29 8.0.0.143 (C636patch01)
Security Patch Level: 2018/08/01 Androld Program Security Patch Level

Use the program (HWOTA8_Mate10) to lower the Firmware as follows:
From the original system BLA-L29C636B143-SP1 (8.0.0.143)
Reduced to BLA-L29C636B128 (8.0.0.128)
After rebooting, the result turns into a black brick. It can't be turned on and cannot be charged, but the computer can find the phone, and the device administrator appears USB SER.

Can this be solved?
thank

Doubtfully, if device is not flashable via testpoints then only main board replacement could help it.

[kenchanfr]

Huawei USB COM 1.0 Drivers Windows 10 64-bit Where to download

Thanks

Sorry to have found it and downloaded it at the same time.

[nar1624]

I cannot flash my device. Please assist.

DC Phoenix username:::: sfc8818




Huawei mate 10 ALP-TL00
Bootloader relocked, FRP locked





Looking for a device in upgrade mode
No devices detected in upgrade mode

Looking for a device in fastboot mode

Device found: 0123456789ABCDEF


10/09/2018 23:34:40 Starting to write device in FASTBOOT mode...

Device found: 0123456789ABCDEF

IMEI: 866215030422106
Build number: :System 8.0.0.38(00KH)
Product model:
Extracting partition XLOADER...
Preparing file to write...

Writing XLOADER partition with file XLOADER
XLOADER partition UPDATE ...FAILED
Cannot get FBlock info from device
Cannot get HW FBlock info from device
Extracting partition XLOADER...
Preparing file to write...

Writing XLOADER partition with file XLOADER
XLOADER partition UPDATE ...FAILED
Extracting partition FW_LPM3...
Preparing file to write...

Writing FW_LPM3 partition with file FW_LPM3
FW_LPM3 partition UPDATE ...FAILED
Extracting partition HHEE...
Preparing file to write...

[manager77]

Kenchanfr...try with google to find ASC-Driver_Handset WinDriver 2.01.00.00.exe

[manager77]

Nar1624...you need testpoint to get Huawei usb com 1...after that you have to flash last boardsoftware 1.0.0.58 from dc phoenix download and flash your phone...

[kenchanfr]

manager77

Has been downloaded

thank you very much

[nar1624]

does not work,I connect USB with phone off/charging, hold Vol- down then ground testpoint, we get a boot to fastboot but I'm not seeing COM port. still in fastboot mode.

[manager77]

Nar1624...you have to disconnect battery first...usb cable must be connected to your phone and not to pc..hold touched testpoint and metal and connect usb cable to pc...wait 2,3 sec until in pc device manager it shows at com ports: Huawei USB COM 1....release the testpoint..done

[AleksandrVZ]

good day!
1.Is the device flashing and how many credits do you need for a regular firmware?
2.Try pressing yes, I will not spoil the device with the appropriate firmware, if I click!

[nar1624]

Yes, it work, unbricked with test point flash.. but lost imei, . enable Manufacture mode repair with HCU client not work. please assite.

New IMEI 1 : 8662150304*****
New IMEI 2 : 8662150304******
New SN : UDN0217A17********
New Vendor : all
New Country : cn
New Model : ALP-TL00
2018-11-02 21:01:59.853 Connecting to server...
2018-11-02 21:02:00.294 Connected!
2018-11-02 21:02:00.309 Open COM port COM10 (Android Adapter PCUI (COM10))...
2018-11-02 21:02:01.268 ERROR!
Insufficient credits!

[Radiotrance]

1. There is a bug with last and all previous DC Phoenix versions regarding "Not erase/write nvm" and "Not erase oeminfo" checkboxes. They do not have any effect unless you check/uncheck them and choose some ANOTHER board software file, NOT THE SAME you had before in the field. If you won't re-choose the file, they won't have any effect either.

2. There is a HUGE problem with 3G networks at least with RNE-, CHM-, NEM- and some other phones. After you restore NV partitions backup, 3G networks would became totally broken. I replaced eMMC with all three forementioned phones and there were no 3G networks at all! While playing with some other NV backups I somehow managed to revive 3G on RNE- phone, but still unable to do that with CHM and NEM. Hardware of the phones is safw and sound, the only problem was dead eMMCs. So there's a big deal about it and we need you to check the procedure and tell us how to repair 3G networks after loosing original NVM partitions.